Ports freischalten beim Netgear FV328

Dieses Thema im Forum "Netzwerk, Telefon, Internet" wurde erstellt von 00johnny00, 6. Juni 2006 .

Status des Themas:
Es sind keine weiteren Antworten möglich.
  1. 6. Juni 2006
    Unten!
     
  2. 6. Juni 2006
    Hi.

    Poste doch bitte mal die genaue Bezeichnung und den Hersteller deines Routers, denn davon hängt der Logon-Name ab. Oftmals sind es aber Admin oder Administrator.

    gruß
    Moo-Gu
     
  3. 6. Juni 2006
    Zur Not: Router resetten / auf Ursprungszustanddingsda bringen, und dann im Handbuch nachgucken. ^^ (Oder kann man den gar nicht ändern?)
     
  4. 6. Juni 2006
    Naja wayne habe es jetzt raus^^

    Nach mehrmaligen ausporbieren verschiedener Namen^^

    closed​
     
  5. 7. Juni 2006
    So neue Frage...

    Wie kann ich beim Netgear FV328 Ports freischalten?

    Hab mal alles durch geschaut, finde aber nix Oo

    mfg johnny
     
  6. 7. Juni 2006
    schau mal ins Handbuch bekommst Du auf der Netgear Page, Hier ein Auszug der Dir helfen sollte.

    Protecting Your Network3-7 Inbound Rules (Port Forwarding)
    Because the FVL328 uses Network Address Translation (NAT), your network presents only one IP address to the Internet, and outside users cannot directly address any of your local computers. However, by defining an inbound rule you can make a local server (for example, a web server or game server) visible and available to the Internet. The rule tells the firewall to direct inbound traffic for a particular service to one local server based on the destination port number. This is also known as port forwarding.Note: Some residential broadband ISP accounts do not allow you to run any server processes (such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location. If you are unsure, refer to the Acceptable Use Policy of your ISP.
    Remember that allowing inbound services opens holes in your firewall. Only enable those ports that are necessary for your network. Following are two application examples of inbound rules:
    Inbound Rule Example: A Local Public Web ServerIf you host a public web server on your local network, you can define a rule to allow inbound web (HTTP) requests from any outside IP address to the IP address of your web server at any time of day. This rule is shown in Figure 3-5:Figure 3-5: Rule example: a local public Web server
    Model FVL328 ProSafe High-Speed VPN Firewall Reference Manual3-8Protecting Your Network The parameters are:
    •Service From this list, select the application or service to be allowed or blocked. The list already displays many common services, but you are not limited to these choices. Use the Add Services menu as seen in Figure 3-4 to add any additional services or applications that do not already appear.
    •Action Choose how you would like this type of traffic to be handled. You can block or allow always, or you can choose to block or allow according to the schedule you have defined in the Schedule menu.
    •Send to LAN Server Enter the IP address of the PC or Server on your LAN which will receive the inbound traffic covered by this rule.
    •WAN Users These settings determine which packets are covered by the rule, based on their source (WAN) IP address. Select the desired option:
    •Any - All IP addresses are covered by this rule.
    •Address range - If this option is selected, you must enter the "Start" and "Finish" fields.
    •Single address - Enter the required address in the "Start" fields.
    •Log You can select whether the traffic will be logged. The choices are:
    •Never - No log entries will be made for this service.
    •Always - Any traffic for this service type will be logged.
    •Match - Traffic of this type which matches the parameters and action will be logged.
    •Not match - Traffic of this type which does not match the parameters and action will be logged.


    MFG Virgo
     
  7. 7. Juni 2006
    Zuletzt von einem Moderator bearbeitet: 14. April 2017
    Dafür haste ne 10 bekommen

    Thx

    So schon wieder ne neue Frage^^: Woran kann es liegen, dass der scheiß Router die Ports nicht freischaltet???


    Bild
    {img-src: http://img475.imageshack.us/img475/2598/bearbeitet10sr.jpg}


    {bild-down: http://img251.imageshack.us/img251/9660/bearbeitet9fg.jpg}

    So sind die Einstelluneg doch eigentlich richtig oder? Oder muss ich bei ICQ aka CIA TCP/UDP machen???
     
  8. 9. Juni 2006
    mach bitte nochmal nen Screen von den Inbound Rules!

    Outbound --> abgehend
    Inbound --> eingehend

    eingehend ist das Portforwarding wenn du da nicht die Ports an deinen Pc weiterleitest geht das nicht, ausgehenden DatenVerkehr(outbound) würde ich Komplett freigeben, es sei denn du hast Leute in deinen Netzwerk die nicht inds I-Net sollen.


    Mfg Virgo
     
  9. 10. Juni 2006

    So also mein Prob ist eigentlich, dass ich alles richtig eingestellz habe, aber kein Port geöffnet wird oO
     
  10. 10. Juni 2006
    Bei Enable ist kein einziger Haken gesetzt daran wirds liegen. Für ICQ brauch man keine Ports freischalten wozu auch? Um Daten zu tauschen gibts bessere Progs.
     
  11. 10. Juni 2006
    LESEN! Outbound alle frei! Aber Inbound nicht!
     
  12. Video Script

    Videos zum Themenbereich

    * gefundene Videos auf YouTube, anhand der Überschrift.